Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
This great article in the next paragraphs on the subject of A Step-by-Step Guide to Installing a Bathtub is absolutely informative. You should take a peek.
Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily available, the task can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Ensure you have qualified yourself for the job and fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new bathtub in your shower room if you have already purchased a new bathtub and also do not require to alter the arrangement of your previous supply of water pipes.
Your devices as well as product list need to make up the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to avoid stress on the tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic because of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of both wood boards under its feet, position the tub in the needed position. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the bathtub must wait up until the bathtub has been made use of at least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the faucet in position with the producer offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The previous kind must be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, causing the water to pass through the wall in between the bathroom and the tiling, resulting in issues with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very serious about How to Install a Bathtub and I am hoping you enjoyed the entire piece. Are you aware of another person who is in to the topic? Do not hesitate to promote it. Many thanks for your time invested reading it.
Click Report this page